Glue-Down Installation of Hardwood Floors

Glue-down installation is one of the earliest ways to put hardwood floors. You’ve found the ideal place to understand the fundamentals of glue-down installation of hardwood floors. DIY hardwood floors installed with the glue-down method are sturdy and long-lasting. The glue-down process of installing hardwood flooring has been around for quite some time and is a tried-and-true method.

Table of Contents

Toggle

Equipment Required for Laying Hardwood Floors

A square-notched trowel, with sides measuring precisely 1/4 inch, is ideal for spreading glue.

Saw dust can get trapped under your floor panels and connecting joints, so have a broom and dustpan handy. The last thing you want after installing hardwood flooring is for it to be uneven.

A carpenter’s crayon sketches the lines of future cuts on the panels. This will also be used to make markings on the floor before laying the boards. Because the glue-down process necessitates such meticulousness, you should always keep this on hand.

A circular saw will be used to sever panels as required. In addition, every eight inches, you’ll make a score in the substrate sheets using your circular saw. This is crucial in preventing panels from curling.

Many hardwood panel kits already include glue for assembly. I recommend Bostik’s Best Adhesive if you need a bond for your hardwood panels.

Nails for Lacework – These are the nails you’ll need to attach the panels to the walls and wall strips.

Sheets of plywood substrate are laid on top of the concrete, supporting your hardwood flooring underneath.

Cloths to wipe up glue drips and messes during the hardwood floor installation procedure. If the glue is left to dry, more work will be required to remove it. After the glue has dried, special chemicals and adhesives may be released. After you’ve installed your hardwood floors, you’ll want to clean them with a soft cloth.

If you need to glue your fingers together, do it to your rubber gloves instead. Also, many dislike the sticky residue that hardwood flooring installation leaves on their hands for weeks afterward.

Getting Ready to Lay Hardwood Floors

When installing hardwood floors with a glue-down method, the surface on which the flooring panels will be placed must be thoroughly prepared. The floor must be smooth, dry, and as clean as possible because this is where you’ll affix the flooring panels that will make up your hardwood floor. Anything that looks like it could be grease or oil should be cleaned up thoroughly before you try to glue it.

It’s also crucial that your subfloor is perfectly flat and level. Obtain some patching cement from the local hardware shop and use it to smooth up the subfloor if necessary.

You’ll also need to decide which of two ways you’ll use glue to install hardwood panels. Hardwood flooring can be installed using the Walk On or Wet Lay methods.

Wet Lay hardwood flooring installation entails spreading adhesive over the subfloor and then setting the hardwood planks directly on top of the glue. Once the bond has gotten sticky, you can move on to the next section. When employing the glue-down method for the first time, it is occasionally recommended that the subsequent panels be placed before the bond becomes sticky, allowing for the panels to be readjusted a few minutes later if they are not lined up correctly.

Hardwood floors laid with the Walk On method necessitate accurate panel placing. To place the panel in the glue, this hardwood flooring method must wait until the glue is quite sticky. This prevents glue from spreading unevenly across your boards as you work. Because of its superior results, seasoned hardwood installers commonly use the Walk On method. Since you’re here reading about it, we’ll assume you’re familiar with the Wet Lay method of installing hardwood flooring.

Hardwood Flooring Installation Guide

First, lay down your substrate sheets over the floor. Make sure it’s flat, smooth, and devoid of any obstructions.

Two, heat the adhesive. It should be warmed to just above room temperature for optimal handling. The glue will be unusable if the temperature is below room temperature.

Third, apply glue to the room’s corner using the square notch on your trowel. Use enough glue to keep the board in place, but save some for later so you have enough to finish the job. You should have bought additional bonds before gluing if you weren’t sure you had enough. If you run out of adhesive before you’re done laying flooring, plan on spending an extra day on the project.

Step 4: After the glue has dried in the corner, lay the first wood panel straight on it. When working with wet cement, it’s essential to get the initial placement of the meeting as perfect as possible to avoid spreading the adhesive as you make subsequent adjustments. If you had used the Walk On approach, the board would have been permanently affixed to the floor within seconds.

Continue adding panels as in step 4 until you reach the final meeting, which shouldn’t fit entirely, and then stop. Mark the board with your crayon and then cut it with your saw.

Six, ensure the first row is firmly wedged in so that the rest of the floor can rest securely on top of it.

Seven, wipe away any excess glue from the top of your first row with a damp cloth before it dries. The bond will harden over time, making cleanup a chore the longer you wait.

To end the first row, you probably trimmed some extra paneling; hopefully, you didn’t mess that up. You’ll be moving on to the next row using that panel. The panels of your hardwood floor will appear better this way, and the surface will be easier to clean.

Put a heavy, flat object on top of the panels’ areas with bubbles, hills, or slopes until the glue bonds them to the substrate.

10) Do some more cleaning. Remove all the glue and sawdust from the area. Mineral spirits applied to a soft cloth can remove any dried glue that may have been missed. Quickly mop up the mineral spirits so they don’t damage the floor. Your floor ought to be brand new hardwood.

Advice from Experience: Laying Hardwood Floors

-Plywood sheets are the ideal substrate material.

-Surface leveling differences can be more easily adjusted if your substrate sheets are thicker. Nonetheless, aiming for a perfectly flat surface before laying down your substrate sheets would be best.

When laying down new panels, use as many flat, heavy things as possible to provide good initial contact with the substrate. Avoid using anything that could scratch your panels. You can always use the panels as a place to rest if you’ve had nowhere else to go. Avoid getting glue on them directly.

You Can Be Confident That Putting in Hardwood Floors Was A Good Decision

It’s time to feel proud of yourself after gluing down your hardwood floor. You won’t have to deal with creaky floor syndrome nearly as much if you install your hardwood floors utilizing the glue-down method and do it right.

I’m crossing my fingers that you paid close attention to the directions and had high-quality flooring. This is due to the difficulty of replacing a glued-down hardwood floor. Unless your need for pleasure is detrimental, of course, you will need a sledgehammer, a crowbar, and a circular saw to remove the hardwood floor that has been cemented down.

Expert flooring and carpet cleaning advice from Niv Orlian, who also runs the website http://www.myflooringhelper.com. To read more about how to install hardwood flooring, visit myflooringhelper.com.

linda